WHAT TO DO IF YOUR WATER HEATER ALL OF A SUDDEN STOPS WORKING

What To Do If Your Water Heater All Of A Sudden Stops Working

What To Do If Your Water Heater All Of A Sudden Stops Working

Blog Article

Get A Free Estimate

In this article in the next paragraph you can discover some very good insight around What Would Cause My Electric Water Heater to Stop Working?.


No Hot Water — Water Heater Repair
Numerous modern residences use an electric water heater for their heating system, as a result of its benefit and ease of use. Nonetheless, much like any other electric devices, problems might occur with its usage, all of a sudden. It can be truly frustrating to awaken to a chilly shower instead of a warm one or having your bath with water that isn't hot adequate and even too warm. Whatever the situation may be, hot water heater issues can be quite aggravating. Thankfully, we have actually made a listing of possible remedies to your water heater issues. There are a variety of elements that can trigger many of these troubles, it could be a concern with the power supply, the electrical heating element, or the thermostat. Prior to doing anything, ensure you shut off the main power supply for safety and security. Whatever the problem is, getting it taken care of ought to not posture excessive of a concern if you comply with these actions:

Inspect Your Power Supply:


As standard as this may appear, it is very essential. Without sufficient power, your hot water heater will not work. So the first thing to do when your water suddenly retires is to validate that it isn't a power issue. Examine if the fuse is blown out or the breaker tripped. If the circuit breaker is the concern, simply transform it off and on once again. Change any busted or worn-out fuse. Evaluate the device with power after these changes to see if it's currently functioning.

Inspect the Burner in the Water Heater:


If it's not a power issue, after that try having a look at your burner if it is still working. Evaluate each of your burner to be sure the issue isn't with any one of them. If any of them is defective, change that component and then inspect whether the warm water is back on.

Check Your Thermostat:


If your water heater still isn't working or the water appearing isn't warm sufficient, you may need to inspect the temperature level settings on your upper thermostat. Guarantee the breaker is turned off before doing anything. Open the gain access to panel and also press the red switch for temperature reset above the thermostat. This must aid warm the water. Turn the circuit breaker back on as well as inspect if the trouble has actually been resolved.

Call A Professional:


If after replacing all defective parts as well as resetting your temperature level, the hot water heater still isn't functioning, you may need to get in touch with a professional plumber for an expert point of view. The trouble with your heating system could be that the hot and cold taps have been switched or it may be undersized for the amount of hot water needed in your home. Whatever the situation might be, an expert plumber would certainly aid address the trouble.

Verdict


Hot water heater troubles are not constantly significant. Many of them result from small concerns like a blown fuse or damaged burner. Changing the damaged components need to suffice. Nonetheless, if you are still incapable to fix the issue, give a call to your nearby plumber to find to get it taken care of.

What Would Cause My Electric Water Heater to Stop Working?


Your water heater is one of the most forgotten-about appliances in your home—until it quits working. Once you realize that there’s no hot water, the water heater jumps up to become the most noticeable appliance you have. No one in your family will be happy until you get the water heater fixed.



To fix an electric water heater as soon as possible, follow the troubleshooting advice discussed below.


Basic Water Heater Troubleshooting


Fortunately, you may be restore the hot water supply simply by resetting the house circuit breaker for the water heater. A tripped circuit breaker is one of the top causes of water heater failures. Shut the hot water heater breaker off then turn it back on. Give the water heater a half hour to heat up (if it’s working) and then check for hot water through one of your faucets.



If you get hot water after resetting the breaker, then the problem may be fixed if the breaker inadvertently tripped and it doesn’t continue tripping.



If the water heater breaker trips again, then you’ll likely need to have a service technician examine and repair the water heater. The service technician will check the circuit breaker and electrical supply wiring for the water heater. A short in the supply wiring or a bad circuit breaker could be causing the breaker to trip. An internal failure such as a broken heating element can also cause the breaker to continue tripping.



When resetting the water heater circuit breaker doesn’t work at all, then the water heater may be getting power while an internal water heater failure is causing the problem.


Conduct Advanced DIY Water Heater Troubleshooting


If the water heater doesn’t work after resetting the high-temperature limit switch, then you’ll need to either conduct some advanced water heater troubleshooting or have a service technician diagnose and repair the water heater failure.



Sears Technicians created a safe and highly-successful DIY advanced troubleshooting video to help you determine the cause of a water heating failure if you want to try to fix the problem yourself. Follow the advice in this video to find and fix the cause of the heating failure on your own:


The video begins with the basic troubleshooting described in the first 2 sections described above. It then goes on to guide you through checking water heater components to safely find the cause of the water heating failure.



If you get to a point in the troubleshooting where you’re not completely confident that you can safely continue, schedule a service technician to diagnose and repair the water heater.



The DIY water heater troubleshooting shown in the above video differs from the diagnosis techniques that service technicians typically use when examining a water heater to find the cause of a heating failure. Safe DIY troubleshooting doesn’t rely on live voltage checks while service technicians often use live voltage checks to quickly find the cause of water heater failures.



While many DIY’ers have been able to find the cause of water heater failures using troubleshooting advice shown in the video, some failures such as a bad circuit breaker can only be found using live voltage checks which should only be conducted by a trained service technician.



Sears Technicians have the training, tools and expertise to quickly find the cause of a water heater failure. Rely on our technicians to diagnose and repair your water heater or any other appliance in your home that quits working.



While the technician is in your home, take advantage of appliance Cleaning & Maintenance offers that the tech discusses with you. Keeping your appliances well-maintained will help them work more efficiently and last longer. Regular professional maintenance will also help prevent costly breakdowns of the appliances you depend on every day.

https://www.searshomeservices.com/blog/what-would-cause-my-electric-water-heater-to-stop-working


No Hot Water — Water Heater Repair

We were made aware of that report on Hot Water Heater Repair through someone on a different web blog. Sharing is good. Helping others is fun. Thanks a lot for taking the time to read it.




See Availability

Report this page